STARTING OSPF PROC  

Friday, November 14, 2008


starting ospf proc

CODE
r2(config-router)#do u all
All possible debugging has been turned off
r2(config-router)#do debug ip ospf events
OSPF events debugging is on
r2(config-router)#router ospf 1
r2(config-router)#network 172.16.23.2 0.0.0.0 area 0
r2(config-router)#net
*Mar 1 00:20:47.943: OSPF: Interface Serial2/1 going Up
*Mar 1 00:20:47.943: OSPF: Send hello to 224.0.0.5 area 0 on Serial2/1 from 172.16.23.2
*Mar 1 00:20:48.055: OSPF: Rcv hello from 192.168.40.1 area 0 from Serial2/1 172.16.23.3
*Mar 1 00:20:48.055: OSPF: 2 Way Communication to 192.168.40.1 on Serial2/1, state 2WAY
*Mar 1 00:20:48.059: OSPF: Send DBD to 192.168.40.1 on Serial2/1 seq 0x4DB opt 0x52 flag 0x7 len 32
*Mar 1 00:20:48.059: OSPF: Send immediate hello to nbr 192.168.40.1, src address 172.16.23.3, on Serial2/1
*Mar 1 00:20:48.059: OSPF: Send hello to 224.0.0.5 area 0 on Serial2/1 from 172.16.23.2
*Mar 1 00:20:48.063: OSPF: End of hello processing
*Mar 1 00:20:48.107: OSPF: Rcv DBD from 192.168.40.1 on Serial2/1 seq 0x1E46 opt 0x52 flag 0x7 len 32 mtu 1500 state EXSTART
*Mar 1 00:20:48.107: OSPF: NBR Negotiation Done. We are the SLAVE
*Mar 1 00:20:48.111: OSPF: Send DBD to 192.168.40.1 on Serial2/1 seq 0x1E46 opt 0x52 flag 0x0 len 32
*Mar 1 00:20:4
r2(config-router)#network 8.167: OSPF: Rcv DBD from 192.168.40.1 on Serial2/1 seq 0x1E47 opt 0x52 flag 0x3 len 52 mtu 1500 state EXCHANGE
*Mar 1 00:20:48.167: OSPF: Send DBD to 192.168.40.1 on Serial2/1 seq 0x1E47 opt 0x52 flag 0x0 len 32
*Mar 1 00:20:48.183: OSPF: Rcv DBD from 192.168.40.1 on Serial2/1 seq 0x1E48 opt 0x52 flag 0x1 len 32 mtu 1500 state EXCHANGE
*Mar 1 00:20:48.183: OSPF: Exchange Done with 192.168.40.1 on Serial2/1
*Mar 1 00:20:48.187: OSPF: Send LS REQ to 192.168.40.1 length 12 LSA count 1
*Mar 1 00:20:48.187: OSPF: Send DBD to 192.168.40.1 on Serial2/1 seq 0x1E48 opt 0x52 flag 0x0 len 32
*Mar 1 00:20:48.207: OSPF: Rcv LS UPD from 192.168.40.1 on Serial2/1 length 136 LSA count 1
*Mar 1 00:20:48.211: OSPF: Synchronized with 192.168.40.1 on Serial2/1, state FULL
*Mar 1 00:20:48.211: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.40.1 on Serial2/1 from LOADING to FULL, Loading Done
*Mar 1 00:20:48.723: OSPF: Rcv LS UPD from 192.168.40.1 on Serial2/1 length 148 LSA count 1
r2(config-router)#network 172.1
*Mar 1 00:20:51.135: OSPF: Rcv hello from 192.168.40.1 area 0 from Serial2/1 172.16.23.3
*Mar 1 00:20:51.135: OSPF: End of hello processing
r2(config-router)#network 172.16.2.1 0.0.0.0 area 0
*Mar 1 00:20:57.943: OSPF: Send hello to 224.0.0.5 area 0 on Serial2/1 from 172.16.23.2
r2(config-router)#network 172.16.2.1 0.0.0.0 area 0
r2(config-router)#
*Mar 1 00:21:00.391: OSPF: Interface Loopback0 going Up -------------> saw this as soon as network is advertised interface goes .. so this is the use of c network command

*Mar 1 00:21:01.167: OSPF: Rcv hello from 192.168.40.1 area 0 from Serial2/1 172.16.23.3
*Mar 1 00:21:01.167: OSPF: End of hello processing
r2(config-router)#
*Mar 1 00:21:07.943: OSPF: Send hello to 224.0.0.5 area 0 on Serial2/1 from 172.16.23.2
r2(config-router)#
*Mar 1 00:21:11.151: OSPF: Rcv hello from 192.168.40.1 area 0 from Serial2/1 172.16.23.3
*Mar 1 00:21:11.151: OSPF: End of hello processing
r2(config-router)#do u all
All possible debugging has been turned off
r2(config-router)#

Design by Blogger Buster | Distributed by Blogging Tips